Plumbing 101: A Necessity for Bathtub Installation
Plumbing 101: A Necessity for Bathtub Installation
Blog Article
Everyone has got their own piece of advice when it comes to Tools You Need to Install a New Bathtub .
Mounting a bathtub isn't exactly brain surgery, but it does need strong plumbing, woodworking, as well as often, tiling abilities. Changing an old tub with a brand-new one is also a moderately challenging project. If the old tub is conveniently accessible, the project can move immediately; if you have to open up a wall to eliminate the old bathtub and place the new tub, the job is a lot harder. In either situation, the task is within a home handyman's skills, although you will certainly need an assistant to vacate the old tub and set in the brand-new one. See to it you have actually qualified on your own for the job and also fit trying it. Rather than working with a specialist to take over a halfway-completed task, it is better to think about employing one before you start. Possibilities are you might need an expert plumber to make tube connections.
This short article will help you mount a new bathtub in your shower room if you have currently acquired a new bathtub and also do not need to alter the setup of your previous water system pipes.
Your devices as well as material list need to make up the following:
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your installment, after that the first thing you should do is separate the water. After doing so, activate the taps to drain pipes any water continuing to be in the system. The process of eliminating the existing taps can be fairly problematic because of the limited gain access to that is often the situation.
Use a container wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipelines to the taps. Have a cloth ready for the remaining water that will come from the pipelines. When the supply pipelines have been gotten rid of, use the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will need to quit the single taps from turning throughout this process. As soon as the faucets have been gotten rid of, the holes in the bath/basin will need to be cleansed of any type of old securing compound.
Before carrying on to fit the brand-new faucets, compare the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new taps to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will need a plastic connector to prevent damage to the string. One end of the port fits on the plastic tail of the faucet and the other end gives a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly call for lowering couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, position the faucet in the installing opening in the bath/basin ensuring that the washing machines remain in area between the tap as well as the sink. Protect the faucet in position with the manufacturer supplied backnut. As soon as the faucet is firmly in position, the supply pipelines can be linked to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with normal tap connectors. The previous kind needs to be connected to the tap finishes initially, tightening up just by hand. The supply pipes can later be connected to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Installing the Bath tub
Utilizing the two wood boards under its feet, place the bath tub in the needed placement. The wooden boards are helpful in equally spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The following goal is to make certain that the tub is leveled all round. This can be accomplished by checking the spirit level and readjusting the feet on the bathtub till the level reads degree.
To set up taps, fit all-time low of the furthest flexible tap adapter to the proper supply pipeline by making a compression sign up with; after that do the same for the other tap.
Switch on the supply of water and also check all joints as well as brand-new pipework for leakages as well as tighten them if needed. Fill the tub and likewise inspect the overflow outlet and the regular electrical outlet for leaks.
Finally, deal with the bathroom paneling as explained in the manufacturer's instruction manual. Tiling as well as sealing around the bath tub must wait until the tub has actually been utilized at least when as this will settle it right into its last setting.
Preparing for the Setup
To start with, the supporting framework provided with the bath must be fitted (if called for) according to the producer's directions. Next off, fit the taps or mixer to the bath tub. When fitting the tap block, it is necessary to make sure that if the tap includes a plastic washing machine, it is fitted between the bath and the taps. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets device to stop stress on the tub.
Fit the versatile tap adapters to the bottom of both taps utilizing 2 nuts and olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet with the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. Make sure you use all of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath ought to now prepare to be suited its last setting.
Tiling Around the Bath tub
In the area where the bathroom meets the ceramic tile, it is essential to secure the accompanies a silicone rubber caulking. This is important as the installation can move sufficient to split a stiff seal, creating the water to pass through the wall in between the bath and also the tiling, causing complications with moisture and possible leakages to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your components and installations. They are offered in tubes as well as cartridges, as well as can sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with twists of drenched paper or soft rope. Remember to constantly load the bath tub with water prior to securing, to allow for the motion experienced when the tub remains in usage. The sealer can split rather very early if you do not take into account this movement before sealing.
Additionally, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally conveniently available on the market. It is a good idea to fit the ceramic tiles making use of waterproof or water-proof adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you really like more info about How to Install a Bathtub Yourself? Write a review directly below. We'd be glad to listen to your opinion about this piece. In hopes that you visit us again in the near future. Please take the time to promote this blog post if you enjoyed it. I praise you for your time. Don't forget to come by our site back soon.
Trusted plumbing solutions at hand. Report this page